• ABS Automated Bleed Routine
• Crank Variation Learn (click here for supported vehicles)
• Injector Flow Rate Programming (CAN-based Diesels)
• SDM Setup and Part Number Programming (click here for supported vehicles)
• Idle Learn
• TDC Learn
• Tire Pressure Sensor ID
• Reductant Fuel Quality Test (6.6 Liter LML '12)

• EVAP Bay Test
• Service Bleed (Non-CAN support not available with ProLine currently)
• Buzz Injector
• Cylinder Contribution Test
• Switch Test
• Glow Plug Test
• System Self-Test
• Low - and High Speed Fan
• All Outputs On/Off
• Injector Coding (1.8L and 2.0L)
• KAM Reset
• Misfire Monitor Neutral Profile Correction
• Tire Size Programming up to 40" ('99-'03 7.3L, and '04-'07 6.0L trucks)
• IVD Initialization
• Steering Angle / Yaw Rate / Acceleration Sensor Reset ('03 Explorer and Lincoln LS)
• Passenger Seat ReZero and Passenger Weight Reset
• Power Seat Calibration Test
• Audio Network Communication Test
• Vehicle In-Motion IO Test
• Front Wiper Self-Test
• Rear Wiper Self-Test
• Diesel Particulate Filter Reset, Clear EGR Adaptive Tables, and Clear Fuel Injector Adaptive Tables
• DPF Regeneration, SCR Dosing Measurement Test, SCR Visual Leak Test
• BMS Reset
• TPMS Sensor Training Mode
• Crash Reset Status (Transit '15+)
• Electronic Parking Brake Maintenance Mode (Fusion HEV '14+)
• Maintenance Mode / Exit Maintenance Mode special function (Edge '16 - '18)
• Windows Reset special function (CMAX '13 - '18, Escape / Kuga '13 - '18, Fusion '15 - '18, and TransitConnect '13 - '18)
• CEI Lock Configuration special function for all supporting models
• DMS Reset special function for Escape / Kuga '13 - '18 and Fusion '15 - '18
• Power Liftgate Initialization special function (CMAX '15 - '18 and Escape / Kuga '13 - '18)
• Valve Calibration special function (CMAX '13 - '18 and Fiesta '15 - '18)
• WMM Calibration special function (Focus '15 - '18 and TransitConnect '13 - '18)

SBEC/JTEC System Tests:

• EGR System Test
• EVAP System Monitor Service Test
• Erase All DTC Fault Codes
• Generate Full Field Test
• Gov & 3-4 Shift Valve Test - JTEC Only
• Leak Detect Pump Test
• Purge Vapors Test
• Reset All Adaptive Memory Fuel Cells
• Reset All Non-Volatile Memory
• Reset CAM/Crank Misalignment
• Reset CAM, Crank, and Sync Status Record
• Reset Duty Cycle Monitor
• Reset Engine Running Time Record
• Reset Fuel Shut-off Record
• Reset Intake Airflow Control Stepper Motor Position
• Reset Trip Information
• Set Sync Signal - JTEC Only
• Set Minimum Throttle Position to Maximum
• Torque Converter Clutch Test - JTEC Only

VPW-based System Tests:

• ABS Bleed Brakes (EBC325, Mk20e, and Mk25e)
• Tire Size Programming
• Transmission Rear/Front Wheel Brake Torque Test
• Transmission Pump Test
• Transmission Quick Learn
• Transmission TCC Break-In Test
• Transmission Front Wheel Pinion Factor

NGC System Tests:

• Injector Kill Test
• NVLD Force Monitor Test
• Purge Vapor Tests
• Reset all On-Board Control Units
• Report Part Number
• Report Reflash Program Counter

CAN-based Module System Test and Configuration Support:

• ABS Brake Bleed
• ABS Initialize ECU
• Auto Door Locks
• Beltminder
• Cylinder Performance Test
• Current VIN Programming
• CAM and Crank Relearn
• DRL Setup Configuration
• EATX Quick Learn
• Engine On Odometer
• IMA Programming Injectors
• Injector Quantity Adjustment
• Module Configuration Setup
• Retrieve Installed Module VINs
• Tire Pressure Sensor ID Programming
• Tire Pressure Trigger Configuration
• Tire Pressure Calibration
• Tire Size Programming

• IVD Initialization (Lateral Acceleration and Yaw Rate Reset)
• Self-Test (RCM and GEM)
• As Built (CAN-based body controllers)
• EPS Steering Calibration
• IVD Initialization
• KOEO
• KOER
• KAM Reset (CAN-based controllers)
• Passenger Weight ReZero
• SWS Calibration

• Air Bleed -- Usual and Master Stroke (ABS)
• ECB Utility -- ECB Invalid, Zero Down, and Linear Valve Offset Calibration (ABS)
• Signal Check (Airbag, ABS, ABS CAN, EFI CAN, EHPS, EMPS, and TPWS)
• Reset Memory (EFI, EFI CAN, ABS, ABS CAN)
• Clear Records (EMPS and VGRS)
• Zero Point Init (EMPS)
• VIN programming
• Sensitivity Check (OCC)
• Inspection Mode (ABS CAN)
• Test Mode -- Zero Calibration (ABS, ABS CAN, TPWS, and OCC)
• Intuitive P/A Detection / Steering Adjustment (Front Sensor, Rear Sensor, and Battery / SAS Replacement)
• TPWS CAN Tire Registration

System Tests:

• Self-Diagnostic (Airbag)
• ECU Part Number (Airbag)
• Diagnostics Record (Airbag)
• Reset ECU (Powertrain)

Work Support/Configuration Functions (Some 01+ and Most '03+)

• Target Idle Ignition Adjustment
• Target Idle RPM Adjustment
• Idle Air Volume Learn
• Self-Learning Control
• Stroke Sensor Zero Point Learning Reset
• Brake Test Count
• ODS Zero Point Reset
• Actuator Zero Point Learning
• Clear Battery Gradual Capacity Loss / Clear Battery Charge Discharge Information
• Position Learning Value Clear / Shift AN Test Count
• Display and Conformation CVTF Deterioration Date
• G Sensor Calibration AT / ECU Part Number AT
• Erase Calibration Data / Erase Learning Value / Erase Memory Data
• GTR Specific Clutch Gear Learning / Show Oil History / High Oil Temp Warning History / Adjust Clutch A and B Capacity / Clutch A and B Touch Point
• Standard Height Level / Adjust Height INI / Clear Height INI
• Auto Activation / Brake Operation / Brake Release / Clutch Sensor Reset / Finish Brake Pad Replacement / G Sensor Calibration / Start Brake Pad Replacement

CAN Module Configurations:

• Door Lock Unlock Set
• Anti-Lock Out Set
• Set IL Door Unlock
• Room Lamp Off Time Set
• Room Lamp On Time Set
• Keyless Entry Horn Chirp Set
• Keyless Entry Hazard Lamp Set
• Keyless Entry Multi-Answer Back Set
• Keyless Entry Auto Lock Set
• Keyless Entry Panic Alarm Set
• Keyless Entry Trunk Open Set
• Keyless Entry Power Window Down Set
• Head Lamp Battery Saver Set
• Head Lamp Custom Light Setting
• Head Lamp Illumination Delay Set
• Wiper Speed Setting
• Security Alarm Set
• Theft Alarm Trigger Erase

System Tests:

• Determine All Systems Present and Operating
• Display Service and Inspection Information
• Display Coding Information
• Self-Test (Safety and Information)
• Steering Angle Adjust (MK20, MK60, DSC 8, EBC 4, DSC 60PP, DSC Premium, EPS, SZL)
• Lateral Acceleration and Pressure Adjust (MK20, MK60, DSC 60PP, DSC Premium [E46 non-M models, E8x, E9x, E6x, and MINI])
• ABS Bleed (MK60 [on E46 '03+, E85/E86, and MINI models])

Service Functions:

• Reset Airbag Light
• Reset Conditional Based Service (E and F Chassis)
• Reset Oil Service Light (for all 9/2000+ models)
• Reset Service Interval Distance and Time (for all 9/2000+ models)
• Register Replacement Battery BMW (E6x/E8x/E9x/Fxx/Gxx)
• Register Replacement Battery MINI (R55/R56/R57/R60/F5x)
• Reset DME, EGS, and RLS Adaptations
• Reset EGS Oil Life Counter (6HP, 6HPTU, GM5, and GM6 units)
• Reset VTG Oil Change
• Set / Cancel Workshop Mode and Startup Electronic Parking Brake (EPB)
• Clear and Set Transport and Sleep Modes
• Window Initialization (E8x/E9x/E60/E61)
• Driver and Passenger Seat Normalization (Fx0)
• Normalize Driver Door for F07 / F10 / F11
• Switch On Compressor Break-In Protection (E60/E61)
• Teach In Clutch Slipping, Teach In Clutch Characteristic Curve, Teach Clutch Values, and Longitudinal Acceleration Sensor Offset (SMG II)
• DDE 5.0 M47 / M57 diesel special function support:
• Air Mass Flow Calibration
• Reset Quantity Mean Value Adaptation
• Reset EGR Calibration to Zero
• Reset Injection Rate Reset Calibration To 100 Percent
• Reset Consumption Calculation Reset To Calibration To Neutral
• Request Particulate Filter Regeneration and Replace of Particulate Filter
• DDE 6.0 N57 and DDE 7.0 N57 / N47 diesel special function support:
• Reset Hot Air Film Mass Sensor
• Reset Exhaust Back Pressure Sensor before Turbocharger
• Reset EGR Valve
• Reset Rail Pressure Regulating Valve Adaptation
• Reset Radiator Shutter Variant
• Reset Electric Fuel Pump Adaptations
• Reset EGR Valve Adaptations

Body Control Module System Tests:

• ATF Replacement
• Diagnosis of Keyless Entry function
• Engine Oil Replacement
• Keyless Entry Registration
• Mission Replacement
• Passcode Clear
• Reset of driver side window position
• Reset of assistant side window position
• Reset of left rear side window position
• Reset of right rear side window position
• Self Diagnostics

Other System Tests:

• ADS Damper Forced Operation
• ADS Jack-Up Stroke Calibration
• ATTS Lateral G And Yaw Rate Calibration
• ATTS Steering Angle Calibration
• Calibrates All Sensor (ABS Type 1 & 4)
• Crank Position Sensor Notch Learn
• DBW Throttle Carbon Clogging Reset
• DBW Throttle Carbon Clogging Status
• Engine Oil Replacement Reset
• OPDS Initialization
• OPDS Sensor Adjustment
• Reset Wheel Speed Pulse Counters (ABS Type 1 & 4)
• Resolver Zero-Position Offset Calibration
• SWS Initialization

• EVAP Leak Test (Siemens 655 [Rev 17, 18, 19], 670 [Rev 8], Bosch COM 1.1)
• Reset Adaptions
• PODS Reset
• WCS Reset
• Read Block Information
• Steering Angle Calibration (ABS/ES 95660 [Rev 23 and 32])

Advanced features besting even the factory solutions:

• Does not require an online account to operate
• View more then 16 sensors at one time
• Faster connections
• More PIDs available on most controllers
• Steering Lock Column Module fully integrated

Service Functions:

• Display Service and Inspection Information
• Display Coding Information
• Reset Service Interval (SI) Distance and Time (for '00+ BMW-based models)
• Reset Service Interval Reset (SIR)
• Steering Wheel Angle Calibration
• Reset DME and EGS Adaptations

• Service Functions:
• Injector Coding (2.0L)
• Brake Sensor Setup
• Display Last Alarm Activations (SLM and GEM)
• Display Fuel Adaptation Tables
• Fuel Adaptation Monitor
• Electronic Parking Brake Release To Service (SType / VPD / XF / XJ)
• Front And/Or Rear Light Calibration (ADHLS and HCM)
• Reset TCM Adaptations (most models)
• Yaw and Lateral Accelerometer Calibration
• Reset ABS Configurations
• System Self Test (SType Only GEM, REM, DDM, PDM)
• EVAP Leak Test (some ECM variations are not currently supported)
• Driver and Passenger Glass Window Calibration (XF / XJ)
• Battery Replacement (XF / XJ)
• Fuel Prime (XF / XJ Petrol / Diesel)
• Clear Adaptation / Purge Self Test (XF / XJ Petrol)
• Particulate Filter Fuel Related Component Replacement / Reset (XF / XJ Diesel)
• Service Reset (XF) Reset DME and EGS Adaptations

System Functions / Work Support:

• Set Mode Steering Angle Sensor
• Lateral and Longitudinal G Sensor Zero Point
• Force Sensor Calibration Mode / Break-In Parking Drive Mode / Parking Brake Removal Mode
• Clutch Sensor Calibration Mode / Parameter Initialization
• ABS Sequence Mode, Brake Maintenance Mode, Check Mode, and VDC Centering Mode
• Permanent Functions:
• Retard Ignition
• Idle RPM Adjustments (with AC and without AC)

System Functions / Work Support:

• Event Memory (Airbag)
• Operating Hours (Airbag)
• Calibration (HBA and Air Conditioning)
• Events and Erase Events (Instrument Cluster)
• Events, Erase Events, and Reset (Instrument Cluster CAN)
• Display Module Information
• Display Vehicle Data (986/987/996/997)
• Headlight system support for the CAN Ext Address protocol (i.e. Macan '15)
• Read and Clear DTCs
• Service Reset for the following vehicles:
  • 911 (997 / 991)
  • Cayenne (E1 / E2)
  • Boxster / Cayan (982)
  • Macan (Cajun)
  • Panamera (G1)
• Cayenne '05 - '09 System tests:
  • Headlight Right Reset
  • Headlight Left Reset
  • Tailgate Calibration
  • Steering Adjustment
  • Longitudinal Adjustment
  • Lateral Adjustment
  • Brake Pressure Adjustment
  • Brake Bleeding
  • Automated Actuations
  • Air Conditioning Flap Motor Installation
  • Air Conditioning General Test
  • Active ESP System Test
  • Added sensor support:
    • Airbag
    • Kessy
    • PSM (MK25)
    • PSM (MK25E1)
    • Tailgate
    • Tire Pressure Monitor

Special Functions:

• ECU Information (All CAN controllers)
• EVAP Leak Test (MFI CAN)
• EVAP Leak Monitor (MFI E200, E400, E500, E600, 1400, and 1600 Series)
• Gas Emissions Test Mode and Sensitivity Check (ABS CAN)
• Reset Learned Values (MFI CAN)
• Zero Calibration (Some OCM CAN)
• SAS Initialization (SAS CAN)
• Steering Angle Initialization and Operation Test (ACD CAN)
• Air Bleed and Lateral G Sensor Initialization (ACD CAN)
• Service Interval Reset (Meter CAN)
• Tire Pressure Sensor ID Check (TPMS CAN (Front Only))

• Adaptation
• ADC Channels
• Module Information
• Module Recoding
• Module Sensor Mapping
• Network Test
• Output Tests (Automatic and Specific)
• Optical Bus Diagnostics (CAN)
• SRI Reset
• Transport Active/Deactivate Mode (CAN)

System Tests:

• AIRMATIC GL Class (X166) and SL Class (R231) Level Calibration

Service Functions:

• Reset Oil Service (ASSYST Plus-based models)
• Reset Oil Service ('03 and earlier with FSS only) and CLS (219), E (211), GL, GLK, and ML (164) and R Class (251)
• Reset Service Interval ('03 and earlier with FSS only)
• Reset General Maintenance (B Service)
• Power Window Denormalization for DCM and LCP controllers
• SBC Deactivation and SBC Activation
• Rodeo, Pitch, Roll, and Move Towards Calibrated Level functions (ABC, ABC221, and ABC230)
• Reset Sensor and Mixture Adaptation (ME2.8)
• Reset ECU
• Reset Adaptation Values, Cold Start Adaptation Values, and Activate Fuel Pump (ME9.7)
• Learn Throttle Valve Stop, Teach-In Ethanol Portion, and Reset Ethanol Teach-In Processes (ME9.7)
• Normalizing of Positioning Motors and Break-In of AC Compressor
• Seat Adjustment Motor Actuators Normalization for ESA controllers
• Reset Quantity Mean Value Adaptation Data (CDI2 - CDI5)
• Re-Initialization of AdBlue Range (CDI6)
• Reset Transmission Adaptations (EGS52, EGS53, and VGS2)
• Wheel ID Registration
• Teach-In Component Yaw Rate and Longitudinal Sensor B24/15
• TPMS Write Identification Numbers
• Reset Offset Value of Signal Steering Angle